New Features
New Features in Cisco IOS XE 17.14.x
The features in the following table are new in this release for the supported
1-Support for Class B End Devices in the LoRaWAN Network
Supported Devices: IR1101 and IR1800
The Cisco Catalyst IR1101 and IR1800 Routers now support Class B mode in LoRaWAN networks. This feature improves network efficiency and extends the battery life of end devices. It works by allowing the devices to open receive windows, known as ping slots, using time-synchronized beacons from the Cisco Wireless Gateway. These windows make it easier for the network server to send data to the end devices.
2-LTE450MHz PIM support on IR1800
Supported Devices: IR1800
The Cisco Catalyst IR1800 Rugged Series Router now supports the 450MHz Long-Term Evolution (LTE) Pluggable Interface Module (PIM), known as P-LTE-450. This module is specifically designed for LTE use cases in utility, public safety, and critical infrastructure sectors in Europe and other regions.
3-Support for CAPWAP and WGB Modes on the Cisco Wi-Fi Interface Module
Supported Devices: IR1800
The Cisco Catalyst IR1800 Rugged Series Routers now support CAPWAP and WGB Modes on the Cisco Wi-Fi Interface Module (WIM). From this release, you can:
- Switch the operation mode between Control and Provisioning of Wireless Access Points (CAPWAP), and Workgroup Bridge (WGB).
- Perform a factory reset and erase configuration.
- Configure the radios for WGB uplink and concurrent Root AP mode operations.
4-Ethernet over MPLS Pseudowire
Supported Devices: IR8340
The Cisco Catalyst IR8340 Rugged Series Router supports Ethernet over MPLS (EoMPLS) pseudowire to transport Ethernet frames across a Multiprotocol Label Switching (MPLS) network. This feature integrates Ethernet-based services into the MPLS infrastructure to deliver Layer 2 connectivity.
Bug fixes
CSCwh77749 :Internal USB hub fails to enumerate resulting in Cellular 0/3/0 not functioning
Platform:IR1101
CSCwh37024 :PnP gets stuck when cellular backhaul is used
Platform:IR1800
CSCwh78779 :P-LTE-MNA I2C issues
Platform:IR1101
CSCwh31936 :SCADA Monitoring Crash with DNP3 on multiple ports of IR1101
Platform:IR1101
CSCwi29218 :Traffic is impacted when HSR link goes down with 100mbps speed.
Platform:IR8340
CSCwh29080 :WP-WIFI6 out of service, error "IM authentication failed for slot/bay 0/3"
Platform:IR1800
CSCwi52138 :Insufficient Power for PoE
Platform:IR1835
CSCwh90300 :Cant establish a session with the 450Mhz modem due to password discrepancy
Platform:IR1101
CSCwi43664 :WP-WIFI6 : Module Out of Service upon reload
Platform:IR1835
CSCwi02277 :Router crashing because of TDL mem leaks
Platform:IR8340
CSCwi10057 :SDWAN: Raw tcp encapsulation command is missing in sd-wan configuration
Platform:IR8340
CSCwi04881 :Async DNP3 port keeps flapping
Platform:IR1101
CSCwi66681 :Modem resets frequently on 17.12.02 with RSSI spikes upto -130 dBm
Platform:IR1101
CSCwh10876 :Ping is not successful after reload the device with switchport config in gi0/0/0
Platform:IR1101
CSCwj54544 :Power usage is at normal level - Events sent every 30 sec
Platform:IR8140
Open problems
CSCwi04881:Asynchronous Distributed Network Protocol 3 (DNP3) port keeps flapping.
Platform: IR1101
CSCwj09554:P-LTE-450 Module ping over VRF fails after reload
Platform: IR1101
CSCwd38611:FN980 modem is not showing in the output of show inventory command after multiple modem-power cycle
Platform: IR1101
CSCvz30726:High CF/TE,Turnaround and Latency number after reload of router
Platform: IR8340
CSCwa92737:Router throws CPP/FMAN download errors on attaching ngsw class-map using etype classification.
Platform: IR8340
CSCwi96187:P-5GS6-GL FN980 modem firmware upgrade failing when two modems on IR1800 IOS 17.12.1a
Platform:IR1800