DigitalMedia update with startup issue and security vulnerability fix

Resolved Issue(s)

✔ ️ Fixed issue causing the system to hang during startup and causing some endpoints to drop offline.

✔ ️Fixed security vulnerability on the DMC-STR, closing port 5555.

Known Issue(s)

? DMC-STR does not upgrade when the unit (8X8/16X16/32X32) is upgraded from 3.02.18 to 3.03.x. See https://support.crestron.com/app/answers/detail/a_id/1001102 for more details.

? Adobe Air version 32 or later must be installed prior to XPanel installation.

? It is recommended to uninstall previous versions of XPanel from Desktop before installing it from DMPS or installation may fail.

? Video wall configuration on DMC-4KZ-HDO cards may be lost after a power cycle or switcher reboot. Wall configuration can be recovered by resending the configuration values from Crestron SIMPL/C# program after chassis has been restarted.

? DM-MD8x8/16x16/32x32-CPU3(-RPS) doesn't support connecting LAN port and Content LAN port to the same subnet

? DM-TX-200-C-2G HID routing may not survive a switcher reboot. The route should be re-established after the endpoint is online

? DM-MD8x8/16x16/32x32-CPU3(-RPS) doesn't support connecting LAN port and Content LAN port to the same subnet.

? Vertical bezel compensation value set from the DM Tool doesn't persist across reboot for DM-RMC-4KZ-SCALER-C, instead set the value programmatically when desired.

? When routing same to more than 8 DMC-4KZ-HDO outputs in DM-MD16x16/32x32-CPU3(-RPS), sporadically some outputs don't have freeze-frame switching.

? When Audio Breakaway is enabled, DM-MD32x32-CPU3 switcher may take additional 15-20 seconds for audio to recover compared to video post reboot.

? Routing an input to all outputs in DM-MD32x32-CPU3 switcher may observe audio double lock during switching on DMC-4K-HDO and DMC-4KZ-HDO outputs.

? DM-MD8x8/16x16/32x32-CPU3(-RPS) web-based XPanel configuration tool doesn't have redundant power supply status.

? DM-TX-4KZ-302-C DisplayPort input doesn't work reliably with USB-C to DisplayPort cables and adapters.

? TT-100 "Connect It" indicators don't work when connected to USB HID port of the DM-TX-4KZ-302/202-C, instead use COMPUTER port on the TX if necessary.

? Audio_Format_fb, Audio_Channel_fb and Audio_Sampling_Freq_fb joins don't work for DMCI-DMC-4KZ-C/-DSP and DMCI-DMC-4KZ-HD/-DSP symbols.

? When switching upstream, 4K/4KZ outputs may have double audio lock with certain LG/Samsung Blu-Ray players.

? When HDR source is routed to DMC-4K-HDO output card, instead of no video it may output bad video depending on I/O signal video resolution. DMC-4K-HDO output card doesn't support HDR.

? DMC-4K/4KZ-DSP input cards do not down-mix DTS:X or Dolby Atmos audio to PCM 2ch audio.

? DMC-4KZ-HD(-DSP) input card setup with DM default 4k 60Hz 2CH/HBR EDID may produce unstable video when connected to certain streaming or Blu-ray players.

? Assigning Global EDID via DM Tool to fully populated DM-MD32x32 chassis may report false failures. Instead, assign input EDIDs in batches; 16 inputs at once.

? The DMC-STR may report a resolution of 0x0@0 when streaming from certain third-party IP cameras.

? Apple keyboard does not connect reliably to RMCs.

? All TXs (except TX-401-XX): HDMI audio unreliable with 480i video. All other resolutions are ok.

? On streaming cards, support for elapsed seconds, bitrate and initiator feedbacks have been removed to work around Crestron ToolboxTM stability issues.

? Streaming unsupported audio ats (e.g., G.711) can cause the DMC-STR to lock up. Use AAC audio.

? Network problems can sometimes cause the DMC-STR to stop decoding a stream. Stop and restart the stream to recover.