Connectivity Update Addresses Fixed Bugs and Known Issues

New Features:

Nothing known

Enhancements:

Nothing known

Fixed Bugs:

• ✔ Fixed issue with cascaded system configurations that enabled disabled ethernet ports during startup. See OLH Answer ID 1000914 for more details.

Open Issues:

• ? With safe cascade turned off, cascaded blade information does not show up after a hot plug of the fiber/cable between the two switchers.
• ? After a reboot or power cycle, XPanel may become stuck on a "system is loading" screen.
• ? Adobe Air version 32 or later must be installed prior to XPanel installation.
• ? It is recommended to uninstall previous versions of XPanel from Desktop before installing it from DMPS, or installation may fail.
• ? Video wall configuration on DMC-4KZ-HDO cards may be lost after a power cycle or switcher reboot. Wall configuration can be recovered by resending the configuration values from Crestron SIMPL/C# program after chassis has been restarted.
• ? DM-MD8x8/16x16/32x32-CPU3(-RPS) doesn't support connecting LAN port and Content LAN port to the same subnet.
• ? DM-TX-200-C-2G HID routing may not survive a switcher reboot. The route should be re-established after the endpoint is online.
• ? Vertical bezel compensation value set from the DM Tool doesn't persist across reboot for DM-RMC-4KZ-SCALER-C; instead, set the value programmatically when desired.
• ? When routing the same signal to more than 8 DMC-4KZ-HDO outputs in DM-MD16x16/32x32-CPU3(-RPS), sporadically some outputs don't have freeze-frame switching.
• ? When Audio Breakaway is enabled, DM-MD32x32-CPU3 switcher may take an additional 15-20 seconds for audio to recover compared to video post reboot.
• ? Routing to all outputs in DM-MD32x32-CPU3 switcher may observe audio double lock during switching on DMC-4K-HDO and DMC-4KZ-HDO outputs.
• ? DM-MD8x8/16x16/32x32-CPU3(-RPS) web-based XPanel configuration tool doesn't have redundant power supply status.
• ? DM-TX-4KZ-302-C DisplayPort doesn't work reliably with USB-C to DisplayPort cables and adapters.
• ? TT-100 "Connect It" indicators don't work when connected to USB HID port of the DM-TX-4KZ-302/202-C; instead, use the COMPUTER port on the TX if necessary.
• ? Audio_Format_fb, Audio_Channel_fb, and Audio_Sampling_Freq_fb joins don't work for DMCI-DMC-4KZ-C/-DSP and DMCI-DMC-4KZ-HD/-DSP symbols.
• ? When switching upstream, 4K/4KZ outputs may have double audio lock with certain LG/Samsung Blu-Ray players.
• ? When HDR source is routed to DMC-4K-HDO output card, it may output bad video depending on I/O signal video resolution. DMC-4K-HDO output card doesn't support HDR.
• ? DMC-4K/4KZ-DSP cards do not down-mix DTS:X or Dolby Atmos audio to PCM 2ch audio.
• ? DMC-4KZ-HD(-DSP) card setup with DM default 4k 60Hz 2CH/HBR EDID may produce unstable video when connected to certain streaming or Blu-ray players.
• ? Assigning Global EDID via DM Tool to fully populated DM-MD32x32 chassis may report false failures. Instead assign input EDIDs in batches; 16 at once.
• ? The DMC-STR may report a resolution of 0x0@0 when streaming from certain third-party IP cameras.
• ? Apple keyboard does not connect reliably to RMCs.
• ? All TXs (except TX-401-XX): HDMI audio unreliable with 480i video; all other resolutions are okay.
• ? On streaming cards, support for elapsed seconds, bitrate, and initiator feedback have been removed to work around Crestron Toolbox™ stability issues.
• ? Streaming unsupported audio formats (e.g., G.711) can cause the DMC-STR to lock up; use AAC audio.
• ? Network problems can sometimes cause the DMC-STR to stop decoding a stream. Stop and restart the stream to recover.

Update Instructions:

Nothing known