Cascaded System Fixes and Known Issues Update Released

New Features:

Nothing known

Enhancements:

Nothing known

Fixed Bugs:

• ✔ Fixed issue with cascaded system configurations that enabled disabled ethernet ports during startup. See OLH Answer ID 1000914 for more details.

Open Issues:

• ? With safe cascade turned off, cascaded blade information does not show after a hot plug of the fiber/cable between the two switchers.
• ? After a reboot or power cycle, XPanel may become stuck on a "system is loading" screen.
• ? Adobe Air version 32 or later must be installed prior to XPanel installation.
• ? It is recommended to uninstall previous versions of XPanel from Desktop before installing it from DMPS to avoid installation failure.
• ? Video wall configuration on DMC-4KZ-HDO cards may be lost after a power cycle or switcher reboot; recover by resending configuration values from Crestron SIMPL/C# program.
• ? DM-MD8x8/16x16/32x32-CPU3(-RPS) doesn’t support connecting LAN port and Content LAN port to the same subnet.
• ? DM-TX-200-C-2G HID routing may not survive a switcher reboot; the route needs to be re-established after the endpoint is online.
• ? Vertical bezel compensation value set from the DM Tool doesn’t persist across reboot for DM-RMC-4KZ-SCALER-C; set the value programmatically.
• ? Routing to more than 8 DMC-4KZ-HDO outputs in DM-MD16x16/32x32-CPU3(-RPS) may sporadically cause some outputs not to have freeze-frame switching.
• ? When Audio Breakaway is enabled, DM-MD32x32-CPU3 switcher may take an additional 15-20 seconds for audio to recover post reboot compared to video.
• ? Routing to all outputs in DM-MD32x32-CPU3 switcher may observe audio double lock during switching on DMC-4K-HDO and DMC-4KZ-HDO outputs.
• ? DM-MD8x8/16x16/32x32-CPU3(-RPS) web-based XPanel configuration tool doesn’t report redundant power supply status.
• ? DM-TX-4KZ-302-C DisplayPort does not work reliably with USB-C to DisplayPort cables and adapters.
• ? TT-100 "Connect It" indicators do not function when connected to the USB HID port of the DM-TX-4KZ-302/202-C; use COMPUTER port instead.
• ? Audio_Format_fb, Audio_Channel_fb, and Audio_Sampling_Freq_fb joins do not work for DMCI-DMC-4KZ-C/-DSP and DMCI-DMC-4KZ-HD/-DSP symbols.
• ? When switching upstream, 4K/4KZ outputs may have double audio lock with certain LG/Samsung Blu-Ray players.
• ? When HDR source is routed to DMC-4K-HDO output card, it may output bad video depending on I/O signal video resolution; DMC-4K-HDO output card doesn’t support HDR.
• ? DMC-4K/4KZ-DSP cards do not down-mix DTS:X or Dolby Atmos audio to PCM 2ch audio.
• ? DMC-4KZ-HD(-DSP) card setup with DM default 4k 60Hz 2CH/HBR EDID may produce unstable video with certain streaming or Blu-ray players.
• ? Assigning Global EDID via DM Tool to fully populated DM-MD32x32 chassis may report false failures; assign input EDIDs in batches of 16 instead.
• ? The DMC-STR may report a resolution of 0x0@0 when streaming from certain third-party IP cameras.
• ? Apple keyboard does not connect reliably to RMCs.
• ? All TXs (except TX-401-XX): HDMI audio is unreliable with 480i video; all other resolutions are OK.
• ? On streaming cards, support for elapsed seconds, bitrate, and initiator feedbacks have been removed to address Crestron ToolboxTM stability issues.
• ? Streaming unsupported audio formats (e.g., G.711) may cause the DMC-STR to lock up; use AAC audio.
• ? Network issues may cause the DMC-STR to stop decoding a stream; stop and restart the stream to recover.

Update Instructions:

Nothing known