DigitalMedia™ Update PUF 3.03.07 fixes several Bugs

Resolved Issue(s)

✔ ️ Fixed issue with some cascaded system configurations that resulted in disabled ethernet ports being enabled during startup. See OLH Answer ID 1000914 for more details.

Known Issue(s)

• With safe cascade turned off, cascaded blade information does not show up after a hot plug of the fiber/cable between the two switchers
• After a reboot or power cycle, XPanel may become stuck on a "system is loading" screen
• Adobe Air version 32 or later must be installed prior to XPanel installation
• It is recommended to uninstall previous versions of XPanel from Desktop before installing it from DMPS or installation may fail
• Video wall configuration on DMC-4KZ-HDO cards may be lost after a power cycle or switcher reboot. Wall configuration can be recovered by resending the configuration values from the Crestron SIMPL/C# program after the chassis has been restarted
• DM-MD8x8/16x16/32x32-CPU3(-RPS) doesn't support connecting the LAN port and Content LAN port to the same subnet
• DM-TX-200-C-2G HID routing may not survive a switcher reboot. The route should be re-established after the endpoint is online
• DM-MD8x8/16x16/32x32-CPU3(-RPS) doesn't support connecting the LAN port and Content LAN port to the same subnet
• The vertical bezel compensation value set from the DM Tool doesn't persist across reboot for DM-RMC-4KZ-SCALER-C, instead set the value programmatically when desired
• When routing the same to more than 8 DMC-4KZ-HDO outputs in DM-MD16x16/32x32-CPU3(-RPS), sporadically some outputs don't have freeze-frame switching
• When Audio Breakaway is enabled, DM-MD32x32-CPU3 switcher may take additional 15-20 seconds for audio to recover compared to video post reboot
• Routing to all outputs in DM-MD32x32-CPU3 switcher may observe audio double lock during switching on DMC-4K-HDO and DMC-4KZ-HDO outputs
• DM-MD8x8/16x16/32x32-CPU3(-RPS) web-based XPanel configuration tool doesn't have redundant power supply status
• DM-TX-4KZ-302-C DisplayPort doesn't work reliably with USB-C to DisplayPort cables and adapters
• TT-100 "Connect It" indicators don't work when connected to the USB HID port of the DM-TX-4KZ-302/202-C, instead use the COMPUTER port on the TX if necessary
• Audio_Format_fb, Audio_Channel_fb and Audio_Sampling_Freq_fb joins don't work for DMCI-DMC-4KZ-C/-DSP and DMCI-DMC-4KZ-HD/-DSP symbols
• When switching upstream, 4K/4KZ outputs may have a double audio lock with certain LG/Samsung Blu-Ray players
• When HDR source is routed to DMC-4K-HDO output card, instead of no video it may output bad video depending on I/O signal video resolution. DMC-4K-HDO output card doesn't support HDR
• DMC-4K/4KZ-DSP cards do not down-mix DTS:X or Dolby Atmos audio to PCM 2ch audio
• DMC-4KZ-HD(-DSP) card setup with DM default 4k 60Hz 2CH/HBR EDID may produce an unstable video when connected to certain streaming or Blu-ray players
• Assigning Global EDID via DM Tool to fully populated DM-MD32x32 chassis may report false failures. Instead, assign input EDIDs in batches; 16 s at once.
• The DMC-STR may report a resolution of 0x0@0 when streaming from certain third-party IP cameras
• Apple keyboard does not connect reliably to RMCs. ? All TXs (except TX-401-XX): HDMI audio unreliable with 480i video. All other resolutions are ok
• On streaming cards, support for elapsed seconds, bitrate, and initiator feedbacks have been removed to work around Crestron ToolboxTM stability issues
• Streaming unsupported audio ats (e.g., G.711) can cause the DMC-STR to lock up. Use AAC audio
• Network problems can sometimes cause the DMC-STR to stop decoding a stream. Stop and restart the stream to recover