MXW firmware 6.4.0 with full live room is now supported

Improvements

• This software release delivers support for the functional capabilities listed below, and visual intelligence to the networked audio devices. This release is supported on both MacOS and WinOS platforms:

1. MXW neXt
2. IntelliMix Room Kits - complete Microsoft Teams Rooms conferencing kits including a compute, touch panel, audio, and video components

Bug fixes

• D-8954: In a rare occurrence, user may notice in P300 design configuration routing lines created outside (in SDC) may do not show up in routing view.
• ID- 8845: In a rare occurrence, the MXA710 device authentication could cause the device to reboot from outside (SDC) of designer.
• ID-8132: The Room preset slot does not properly detect a conflict state when a missing device which comes back online has different preset name in slot 1 when compared to other online devices in the room.
• ID-8186: MXA910, MXA310 and ANIUSB-MATRIX devices password state incorrectly changed to locked state even if they are unlocked in same designer session, and Deployment failed is displayed
• ID-7760: When you create a live room with MXA310 and MXA910 devices, set a password, and then attempt to import presets for individual device creates an authentication loop where the user no longer can access the device.
• ID-9350: Designer application may sometimes fail to complete saving room design file fully. This anomaly happens when file save workflow is interrupted, resulting in the inability to open the saved file.
• ID-8624: MXN-AMP analog outputs are disabled when Output mode is switched between LoZ and 70V mode.
• ID-8732: MXN-AMP outputs tab displays the channel output label “Speaker Output” instead of “Analog output”.
• ID-8601: Designer does not show the Allow Firmware Downgrades option in the Services tab of the MXN-AMP
• ID-8746: MXN-AMP Matrix Mixer behavior in 70V mode could automatically show Dante Output 1 routed to all Input channels
• ID-9402: Loading design from RDF file containing duplicate channel names results in deployment failure
• ID-9350: Corrupted room file when closing Designer
• ID-7058: Changes of MIC optimization mode is not reflecting on P300 Live device after device import
• ID-5962: Automatic conflict resolution is not happening in empty online room
• ID-7174: User is not able to delete routes / remove unlocked devices from a room with DDM locked devices
• ID-7171: Routing warning snack bar is not displayed for unlicensed IMXR DDM locked device.
• ID-6388: Filtered devices in online devices page is not persisting after switch views
• ID-6429: Stepper button is missing for gain field coverage property panel
• ID-6460: Delay on password selection when deploying mixed password case rooms
• ID-6450: Room conflict resolution is not happening in online protected room
• ID-7305: Delay in importing device presets for all devices
• ID-6230: Restore default settings operation may cease working for MXA901-R SDC
• ID-6920: MXA902 settings may not persist after preset import
• ID-6220: MXA901-R deployment may fail when pushing name to dante devices
• ID-8254: Switching a preset erases rooms background image
• ID-6298: Coverage area "jumps" when resized in Online room
• ID-6293: Intermittent clear room process failure
• ID-6257: Scrolling bar visibility on online device page
• ID-7760: MXA310 and MXA910 may get stuck in authentication loop after importing preset
• ID-7349: Designer 6 may freeze and has to be manually shut down within 30 seconds of opening app.
• ID-8242: PEQ values may not persist for MXA710, MXA901-R, and P300 devices.
• ID-8182: Preset slot 1 should get into conflict state when different preset names present inside slot 1.
• ID-8186: Devices password state changed to locked state even if they are unlocked in same designer session and Deployment failed is displayed
• ID-8221: Status of AEC ref route in red color after performing rekey audio encryption.